Button fell out

  • Thread starter Thread starter tinpanalley
  • Start date Start date
  • Replies Replies 23
  • Views Views 2K
tinpanalley

tinpanalley

Member
I've got a little black button with three small legs/pegs that has fallen out of one side of the footwell. Anyone seen one of these and happen to know how to put it back? One of the three pegs keep sbending back when I try to put it back in its place. Any tips?
 
Sounds like a plastic fastener, they don’t usually come out unless they were broken or installed incorrectly. the center part needs to be pulled up before trying to reinsert.

This video goes over the basics -
 
tinpanalley said:
I've got a little black button with three small legs/pegs that has fallen out of one side of the footwell. Anyone seen one of these and happen to know how to put it back? One of the three pegs keep sbending back when I try to put it back in its place. Any tips?
Click to expand...
Photo, please?
 
You'll ahve to excuse the cat hair and mess, we've been moving.
DSC_1764 (2).webp


DSC_1764 (2).webp
 

Attachments

  • DSC_1765 (2).webp
    DSC_1765 (2).webp
    38.2 KB · Views: 18
tinpanalley said:
You'll ahve to excuse the cat hair and mess, we've been moving.
Click to expand...
The cat probably pulled the button out! Bad kitty!

I'm trying to imagine what the button with "three small legs/pegs" looks like (I'm afraid to yank out the button in my SE to see it). I wonder how the button is installed at the factory?

Are the legs flexible enough that you could you wrap a thread around the legs to collapse them enough to get the button into the hole? Then you could pull the thread out to allow the legs to expand and hold the button in place.
 
insightman said:
The cat probably pulled the button out! Bad kitty!

I'm trying to imagine what the button with "three small legs/pegs" looks like (I'm afraid to yank out the button in my SE to see it). I wonder how the button is installed at the factory?

Are the legs flexible enough that you could you wrap a thread around the legs to collapse them enough to get the button into the hole? Then you could pull the thread out to allow the legs to expand and hold the button in place.
Click to expand...
That....is.. probably something that could work....
I of course, left it in the car, so I can't send a picture of it right now. I'll send it tomorrow.
 
tinpanalley said:
I've got a little black button with three small legs/pegs that has fallen out of one side of the footwell. Anyone seen one of these and happen to know how to put it back? One of the three pegs keep sbending back when I try to put it back in its place. Any tips?
Click to expand...

I had that happening on one of those fasteners - when i unplugged the phone charger (plug is right behind that area). I pulled out the center pin and kept bending the rogue peg until it was straight enough to go in without bending backwards. You can put the center pin back in after you get the fastener in the hole.

I hate poorly designed push clips and i consider these to be those.
 
Yeah take the middle pin completely out of the clip. This will make it easier to bend the 3 pegs straight enough, so that you can insert the clip back into the hole in the interior panel of the console. After the clip is back in the hole, then insert the middle pin back into the clip to secure everything.

It's not real easy. You have to play with the clip and it's 3 bendy pegs and get that sucker back into the hole. It's a bad design.

20221012_154821.webp


20221012_154841.webp
 
Has anyone else noticed that the current young generation pronounces /buh' tuhn/ this way:
/buh' uhn/ ?
Really hurts my ears.
 
F14Scott said:
Has anyone else noticed that the current young generation pronounces /buh' tuhn/ this way:
/buh' uhn/ ?
Really hurts my ears.
Click to expand...

Count your blessings. I grew up in East Tennessee, and I pronounce wash as 'warsh'. I get a lot of odd looks when I talk about the politicians in Warshington.
 
In my checkered employment career, I once worked in a gas station with a charming fellow from Alabama who used words like "tar" and "awl" (and he wrote them that way, too). Don't forget to ask the customer if they'd like their "awl" checked, or if their "tars" needed air.
 
I was astounded when someone "out east" told me I had a Michigan accent!

Edit: I was only 21--a young idiot who believed everyone else had an accent, not me!
 
Last edited:
A coworker is from a smaller town outside AA, and he most definitely has an eastern-Midwestern accent.
 
You must log in or register to reply here.
Back
Top